#Faux patina paint job how to
#Faux patina paint job full
#Faux patina paint job free

The top here is a wet layer of Bronze with an even, light layer of Green Patina Sprayed across the top. A Few More Variations with Bronze and Copper Paints The bottom is a wet layer of Copper sprayed with enough Blue Patina to make it run a little. The top is a layer of wet Bronze sprayed with enough Green Patina to make it run in a few places. I decided to prop these canvases against a box and let the spray drip down the canvas as it dried. The bottom is Copper Paint with Blue Patina. The top is Bronze Paint with Blue Patina. This gives an overall patina look with the drops on top.

Lightly spread the patina over the wet paint with a foam brush, then sprayed a few more times over that. I created this look by applying a coat of the metal paint, then spraying a few times with the patina. Patina Paint Oxidized Copper & Bronze Metal Paint Finishes Just barely dab the end in paint and lightly blot on a paper towel before brushing it on your DIY Faux Patina Paint look. Once that reacted and dried, I used a cheap Chip Brush to dry brush fine lines of the Iron Paint and Vintage Duck Egg over the rust patina.Ĭhip Brushes are great for dry brushing since the bristles tend to be a little uneven. I started with a wet layer of Iron, then sprayed Green Patina on that and lightly spread it across the surface with a foam brush. The bottom has a thick coat of Iron Paint with just a few light sprays of Dixie Belle Green Patina.īoth of these are Iron Paint, Green Patina, and Dixie Belle Vintage Duck Egg. I probably sprayed 8 times on the lowest setting. Just make sure it isn’t so wet that it won’t dry. I applied a thick coat of Iron, then sprayed the top with enough green patina to make it pool up in that area that has that great rust explosion look.

#Faux patina paint job how to

But the results are gorgeous! 🙂 How to Patina Paint An Oxidized Iron Rust Paint Finishīoth of these are Iron Metal Paint with the Green Patina Spray. Of the 3, Iron seems to take a bit longer. And it can take 2-6 hours for the Patina to fully develop.īut, you will see it start almost immediately. That will provide the strongest reaction. Now that I’ve covered how you get started, let’s move onto How to Patina Paint Metal Finishes! Dixie Belle does recommend using the sprays on a wet layer of the metal paint. BUT you could start with a dark shade of Dixie Belle Chalk Paint as the base.

#Faux patina paint job full

The Iron required 4 or 5 to get full coverage over the blue. The Copper and Bronze Paints only require 2 coats for full coverage. This next photo was taken after applying 1 coat of the metal to the Vintage Duck Egg paint. That metal primer protects the real metal from the oxidizing spray.ĭixie Belle Vintage Duck Egg Chalk Paint on 12 canvases. If you’ll be painting actual metal, you should use the metal primer that is available with these metal paints. Then you apply a second coat of the metal paint and spray on the patina while that 2nd coat is still wet.

Then apply 1 coat of the metal paint and let that dry. You start a faux finish with a base coat of a Dixie Belle Chalk paint, in any shade you’d like. Read the full disclaimer here.Ī peek at the Dixie Belle Chalk Paint and Metal Finishes I used. I would never recommend something that I wouldn’t pay for. But as always, my opinion and review of the product are my true reaction and opinion about this product.

#Faux patina paint job free

I was provided free product for this post. Have fun and be sure to check out my YouTube Channel for more easy DIY home décor tutorials. Or paint lines of the patina spray in veins across the paint. Maybe you want to mix a couple metal paints on the same piece. These are just a starting point for your DIY Faux Patina Paint Metal Finishes. Hopefully, these 20 examples show you how to patina paint and help you pick the metal and patina finish you love.